Plumbing 101: A Necessity for Installing a Bathtub
Plumbing 101: A Necessity for Installing a Bathtub
Blog Article
They are making a number of great points on the subject of Installing A Bathtub in general in the article down below.
Installing a bath tub isn't precisely rocket science, however it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Changing an old tub with a new one is likewise a reasonably difficult job. If the old bathtub is readily easily accessible, the project can move easily; if you have to open a wall to get rid of the old bathtub and place the brand-new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's skills, although you will require an assistant to move out the old bathtub and embeded in the brand-new one. See to it you have actually qualified yourself for the task and are comfortable attempting it. Rather than working with a professional to take over a halfway-completed project, it is better to think about utilizing one before you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly assist you set up a new bath tub in your shower room if you have currently gotten a new bathtub as well as don't require to alter the arrangement of your previous water pipes.
Your devices and product checklist need to make up the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is separate the water supply. After doing so, turn on the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing faucets can be fairly troublesome because of the limited gain access to that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a towel ready for the staying water that will come from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. When the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Prior to carrying on to fit the brand-new taps, compare the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will require a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end gives a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in area in between the tap and the sink. Safeguard the tap in position with the maker offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former kind should be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bath tub
Making use of both wood boards under its feet, place the tub in the called for position. The wooden boards are handy in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 small points.
The next goal is to guarantee that the bath tub is leveled all round. This can be attained by examining the level as well as changing the feet on the tub up until the spirit level checks out level.
To set up taps, fit the bottom of the outermost versatile tap adapter to the ideal supply pipeline by making a compression sign up with; after that do the same for the various other tap.
Switch on the water as well as examine all joints as well as brand-new pipework for leaks and also tighten them if required. Load the bathtub and likewise check the overflow electrical outlet and also the normal electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait until the tub has been utilized at the very least when as this will certainly resolve it right into its last placement.
Preparing for the Setup
To start with, the sustaining framework supplied with the bath must be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the faucet features a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the taps system to prevent stress on the bath tub.
Fit the adaptable tap ports to the bottom of the two faucets utilizing 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should currently prepare to be suited its final position.
Tiling Around the Bathtub
In the location where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to fracture a stiff seal, causing the water to pass through the wall in between the bathroom as well as the tiling, leading to issues with dampness as well as feasible leaks to the ceiling below.
You can pick from a variety of coloured sealants to blend in your components and also fittings. They are offered in tubes and cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to permit the motion experienced when the bathtub is in use. The sealant can fracture rather very early if you do not think about this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly available on the marketplace. It is a good idea to fit the tiles utilizing water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am just very drawn to A Step-by-Step Guide to Installing a Bathtub and I really hope you enjoyed our page. Liked our post? Please share it. Let someone else find it. Thank you for going through it.
Fix it ASAP! Call. Report this page